This page is for all types of surface drills used for mud rotary,diamond,R/C and aircore methods of drilling. We will have other drills available that are not listed on this page, so send us an email and let us know what you require. We are always looking for more stock so if you are looking to sell please send all information regarding your drill via our feedback page, or to our email address listed at the bottom of this page.

_______________________________________________________________________________________

X300 AC drill rigs

Welcome to the best new aircore / RC and Rab drill available on the market today. These drills have been fully engineered for reliability and strength. The total weight of the drill units is just on 10,750 kgs and is ideal as a frontline exploration

drill that is easy to operate , and is fitted with all safety features you will ever require. These drills have been built so they fit into a 20 ft sea container , for shipping anywhere in the world. Please read through the specifications listed below and

give us a call to find out more .

Mast
- Compact box section mast structure, 5.2 metres overall length (plus winch and table foot).
- Heavy-duty dump mast plate with single hydraulic cylinder providing 1.8 metre dump stroke.
- Twin hydraulic mast raise cylinders.
- 3.5” bore x 2” rod x 75” stroke feed cylinder actuating 2:1 ratio travelling sheave system providing 3.8 metres of rotation head stroke.
- Rapid head traverse speed (4.2 seconds top to bottom, 2.8 seconds bottom to top).
- Variable pull-back and pull-down fine feed control.
- 5,500 kg pull-back capacity with dual heavy duty pull-back and single pull-down leaf chains.
- Slips table assembly with air actuated upper and lower Bisalloy rod spanners and hydraulic cylinder mounted to suit breakout wrench.

Rotation Head
- 4000 drive head with heavy-duty hardened and ground gears.
- Travelling head plate mounted to mast via 4 heavy-duty large diameter adjustable vee rollers.
- Twin hydraulic rotation motors providing 4000 Nm of rotation torque at 85 rpm.
- 0 to 170 rpm speed range.
- 70mm diameter hollow bore spindle.

Base
- 4.3 metre long rig base x 2.3 metres wide to fit inside standard sea container.
- Design to suit crawler track frame and/or truck fitment.
- Rear hydraulic stabilising jack legs fixed into rig base.
- Front hydraulic stabilising jack legs, each side incorporated into hydraulically extendable frame.
- Independent tilting, dumping & sliding rod bin - 30 x 3 metre (3½”) rods = 90 metre capacity.

Power Unit
- Caterpillar 3406 diesel engine producing 440 horsepower at 1800 rpm.
- Atlas Copco 2-stage ORV10 compressor air-end and receiver tank package providing 600 cfm
  at 250 psi. Driven directly from rear of Caterpillar engine.
- Hydraulic pump group direct coupled to front of Caterpillar engine consisting of:
1 x Rexroth A10V100 piston pump (171 litres/minute @ 3500 psi)
1 x Rexroth A10V71 piston pump (121 litres/minute @ 1500 psi)
1 x Parker triple gear pump (2 x 39 litres/minute @ 2500psi, Pilot 27 litres/ minute @ 700psi)

Miscellaneous
- Double element filtration for engine and compressor air inlets.
- 450 litre capacity hydraulic oil tank with level sight glass and return & case drain filtration.
- Hydraulic pressure filtration.
- Allied upright cooler pack (rated to 55 degree C ambient) incorporating engine water radiator, compressor oil, hydraulic oil & diesel fuel coolers. Hydraulically driven fan motor.
- FMC A0413C vertical piston water pump.
- Top of mast mounted survey winch with brake.
- 24 volt electrical system including heavy-duty battery box and emergency stop buttons.
- Safety guarding to moving components.
- Fold up driller’s platform.
- All fabricated components sand-blasted prior to painting. All components primed and top coated with high quality 2-pack urethane paint in the customers colour of choice.

ADL Series HD900 Drilling Rig

Mounted on steel track base

Specification

·         6m Dump Mast

·         'P' Head with 4" drive chain

·         3.5 metre stroke

·         PPFMC Pump AW1122, 37 gpm, 1000 psi

·         15,000lb winch complete with spare 16mm winch rope 

·         Mounted on steel Strickland track base

·         Offsider Hinged Platform complete with support bar

·         Engine Cover (2 door)

·         Double V Hydraulic Foot Clamp with 3 slips

·         Mud Mixer

·         6 mtr suction hoses and foot valve

·         Kelly hose (10 metre) x 1”

·         3 sets of Chuck Jaws – P, H, N

·         1000m 6mm wireline

·         5.9litre 6BTA Cummins Engine (Murphy shutdown system) with engine cover

·         2 x Emergency Stop

·         Battery Isolator fitted to battery box

·         140 litre aluminum fuel tank

·         Rexroth Hydraulic componentry

·         Operation & Parts Manual

·         Factory warranties apply.

·         Rig painted New Cat Yellow using Altex 2 pac industrial paint

·         Fitted into 40ft HC certified container

UDR 200

2007 model with less than 3000 hours . The drill is fitted with a PQ head and the capacity is NQ - 1200 mtrs HQ - 800 mtrs and PQ - 400 mtrs. The drill is fitted with triplex pumps and safety cage. This is a nice straight drill and is ready to go

to work. The drill is located in QLD and is selling for $420,000.00+ GST

Boartlongyear LF90s

We have five units available in either jack up or skid bases. The units are in good condition and have various hours and years. Please call to discuss the options

MAN / Sullair air truck unit

Complete air truck setup mounted on a 2003 6 x 4 MAN truck showing 130ks. The compressor is a Sullair 1150cfm x 350 psi in cabinet and is five years old. The booster is a Keypower built 1800cfm x 800psi boost capacity. The condition of all

equipment is very good and is available immediately. The selling price is $295,000.00 + GST

MAN Ingersoll Rand air truck unit

Complete air truck setup mounted on a 2003 model 6 x 6 MAN with 55000 ks on the clock . The compressor is a Ingersoll Rand 900cfm x 350 psi unit with 8000 hours on the clock. The booster is a Keypower built 1800 cfm x 800 psi

The truck has just been serviced with a new gearbox fitted . The condition of all equipment is in good condition. Selling price $320,000.00 + GST

Schramm T450

2003 model showing 6000 hours on the clock . The drill is fitted with a 900cfm x 350 psi onboard compressor. The drill has just been through the workshop and is ready to drill. The drill is located in QLD and is mounted on a 6 x 4 International .

The drill is fitted with dump mast and survey winch, and is selling for $500,000.00 + GST

Continental –Emsco DA 500 Duplex Mud Pump.

Max liner size 7 ½”

Stroke : 16”

Currently set up with 6” liners that will give 468 US gals at 1566 Psi. Can be kitted up to 7 ½” to give 751 US Gals / Min at 65 strokes At 970 Psi , or can be kitted down to 4 ¾” to give 268 US Gals / Min at 65 strokes and 2720 Psi.

The whole pump unit is mounted on a jack up base for ease of moving. The unit is in good condition and available now. Selling price $275,000.00 + GST

Desco 6500 multipurpose drill

This is a 2011 model with less than 2000 hours on the clock. The capacity is 2000 mtrs NQ / 1400 mtrs HQ and 400+ mtrs open hole . The drill is Australian compliant and is ready to go to work. Located in Western Australia

and the selling price is $380,000.00 + GST

Jacro 500

Mounted on a Hino 4wd 750 truck this is a nice straight drill fitted with a onboard Sullair style cabinet unit 400cfm x 200 psi compressor.  The drill was fully rebuilt last year and is setup for 75mm aircore rods and is fitted with

all aircore sampling equipment. This drill won't last long and is priced to sell at $270,000.00 + GST  

KRM 4900 custom drill

This is a purpose built water boring drill and has 300 hours on the clock. The drill is being sold with a list equipment so the drill is ready to go to work. The drill is mounted on a 2009 Fuso rwd truck that has done only 3000 ks.

The selling price is $270,000.00 + GST

Hanjin D& B 10D

We have available a new multipurpose drill ex stock. The drill is setup for coring / DTH / auger / mud rotary and air drilling. The unit comes complete with wireline and haul winches with winch extension fitted.

The drill also has a triplex pump and dump mast , the engine is 105 hp Hyundai water cooled diesel . The drill offers 10 ton pullback and a slewing 3 speed rotation head with a max speed of 1100 rpm. These units

are fast becoming market leaders in Australia , and they are great quality and price. Hanjin also offer multipurpose drills with 2000 mtr NQ capacity and have RC capability , in either truck or track mounted versions.

The selling price on the Hanjin D& B 10D multipurpose drill is $185,000.00 + GST. Please note that Hanjin offers a nation wide warranty on all of their new drills.

 Drill Rig ID 18 1500 NQ Multipurpose Mounted on ex Nato 8x8 Mann truck LHD.

 Drill rig has 101 hrs since complete rebuild.

 Stripped bare with hydraulics motors individually tested with anything less than 100% replaced by Berendson.

 Complete re-hose by Berendson.

 System to incorporate pull down back function as per UDR operation

 All hydraulic work completed by Berendson.

 Rig Engine re-built by Keypower

 Ropes all renewed

 Machinery Guarding / Electrics / Decks upgraded in line with MDG15 compliance.

This drill is being sold as a bare drill but there is a list of additional equipment that can be purchased with the drill, including compressors , rod loaders etc. The drill is selling for $500,000.00 + GST

ROTARY DRILLING RIG MODEL MR 2000

We have just listed this late model low hour machine in excellent condition and located in W.A. This machine would suit someone looking for a new drill with plenty of power and reliabilty. The selling price for the bare drill is $375,000.00 + GST

Rotary drilling rig capable of drilling to a depth of:   1200 mt with 3 ½  inch rods up to 8 inch diameter  - 920 mt with 4 ½  inch rods up to 12 inch dia - 1200 mtrs NQ diamond core Conventional mud rotary /air/DTH drilling and set for handling

 25 inch casing in 6 metre lengths.

Geoprobe 6620 DT models

We currently have two units available with very low hours . The drills are being sold bare , and prices start from $87,000.00 + GST 

Complete RC drilling outfit SCHRAMM T685

If you are looking for a complete Reverse Circulation drilling outfit , look no further. Just listed and new to the market we have the following rig and equipment for sale.

·         Schramm T685 fitted with cyclone/splitter

·         Onboard Sullair 800cfm x 350psi compressor.High end recently replace with a CVS reconditioned unit.

·         Detroit 12v-71 powers all hydraulics ( also comes with a spare 300 hours old fully rebuilt engine)

·         Leader A8-208 additional support compressor truck. Fitted with a Caterpillar 3208 V8 turbo engine.

·         Auxillary compressor is a Sullair 1350cfm x 350psi , powered by a C10 Caterpillar engine with 629 hours.

·         Air research booster compressor, with 1000psi output and powered by a C9 Caterpillar engine with 293 hours.

·         All pressure vessels have been recently x-rayed and tested

·         Mercedes 6 wheeled 2222/48 rod truck complete with 250 mtrs of 6 mtr RC drill pipe.

The selling price is $1.65 million Australian Dollars , and is ready to go straight out to work. All equipment has been serviced regularly and is in good working order. This outfit would suit both serious contractors, and mining companies.

Send mail to rigsale1@bigpond.net.au with questions or comments about this web site.
Last modified: 3/5 /12